Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Have you been on the lookout for help concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably hard job. If the old bathtub is conveniently available, the job can relocate rapidly; if you have to open a wall to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make sure you have certified yourself for the work as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one before you start. Opportunities are you may require a professional plumber to make tube connections.
This short article will aid you install a brand-new tub in your restroom if you have currently purchased a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your tools as well as material list should consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing taps can be fairly bothersome because of the limited access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bath tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the tub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub should wait till the bath tub has been used a minimum of when as this will resolve it into its final position.
Preparing for the Setup
Firstly, the supporting frame provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always load the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can crack fairly very early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles using water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our part on Tools You Need to Install a New Bathtub . Thanks a lot for spending some time to read our post. Enjoyed our entry? Please share it. Help somebody else locate it. Thanks a lot for your time. Come back soon.
Go Deal Now Report this page